Clean Urine

Collection Container

This clean urine collection container holds approximately 3 ounces (90mL) of solution which is the volume required for one test according to standard guidelines. This clean urine container has a removable screw cap and wide opening for filling. This compact container is thin and can be concealed in a pocket or worn under clothing without being noticeable. An easy-to-read temperature indicator strip is placed on the container to provide assurance that the temperature of the clean urine solution is within the acceptable range of 90°F - 100°F.

Synthetic Sample

This powdered synthetic human clean urine sample is certified to be 100% toxin-free. This synthetic clean urine is laboratory grade and is used by many facilities to calibrate testing equipment. It is undetectable and contains the same characteristics of human urine (creatine, specific gravity and balanced pH). It also does contain uric acid which is important today to confirm validity. Unlike real human urine, this synthetic clean urine is not a bio-hazard and you cannot contract any infectious diseases. This clean urine sample is unisex for male or female use. Unlike other clean urine, this does not require refrigerating, freezing, or thawing.

Heat
Activator

This unique heat activator is an idea heat source. This chemical heat activator brings the clean urine solution to the acceptable temperature range within seconds and maintains the proper temperature for approximately 20 minutes. No microwave is needed. It does not require expensive bulky battery powered heating devices or heating packs (ie: hand warmers) which can take up to one full hour to heat/cool the clean urine sample to the proper temperature and can also cause skin burns. Heating pads can also be inaccurate by making the sample too hot or too cold.

CAUTION: Not for human consumption. Harmful if swallowed. Avoid contact with skin, flush affected area with water. Keep out of reach of children. NOTE: This clean urine product is not a medical device.

Step One

Carefully fill the plastic clean urine Mixing Container with lukewarm water (tap or bottled) up to the highest graduation line found just below the bottle neck (see bottle illustration above). The water used should be near room temperature (approximately 65°F to 70°F). It should not be too hot or too cold. Using near room temperature water will make it easier to gage the amount of Heat Activator needed in step 3.

Note that it is very important NOT to open Synthetic Sample or Heat Activator vials prior to use. Opening vials prior to use will significantly decrease the products effectiveness and its overall shelf life, also voiding its guarantee.

Step Two

Synthetic Sample- Add the entire contents of the Synthetic Sample vial to the water in the Mixing Container, screw cap on bottle and gently shake container until the powder has completely dissolved. (Synthetic Sample of clean urine can be premixed with water up to six hours prior to testing).

Step Three

Heat Activator- Note that the use of the Heat Activator is optional; its sole purpose is to heat the solution to near body temperature. Therefore if prior to submitting your sample, you notice that the solution temperature is already within the proper temperature range of 92°F to 98°F (indicated in green) then you may skip Heat Activator step and move on to step 6.

IMPORTANT: If or when concealing the clean urine Mixing Container, never place the Container’s temperature strip next to or against your skin as this may lead to a false temperature reading!

For easy pouring; verify that the Heat Activator content is in a "loose" or "free flowing" granular form. If the granules are in a solid partially solid form, simply tap the vial against a hard surface, this break down any clumps and bring the Heat Activator back to it’s original granular form.

The principle behind the Heat Activator is: The lower the temperature of the clean urine solution = the more Heat Activator will be needed. However be very cautious as to the amount of heat activator used, you must avoid overheating the solution.

Guidelines to the amount of heat activator needed: If you do not see any temperature indication on the strip, this means your sample temperature is below 88°F. In this case we recommend that you carefully add 1/3 of the Heat Activator into the clean urine Mixing Container.

If the temperature on the strip indicates a solution temperature of 88°F to 92°F then we recommend that you only add 1/4 of the Heat Activator into the Mixing Container.

Caution: Adding an excessive amount of Heat Activator may overheat the clean urine solution; very rarely one will need to use more than 1/2 of the Heat Activator without overheating the solution! If the temperature of the solution rises above 98°F, let it cool down by laying the Mixing Container of clean urine on the coldest surface available with temperature strip facing up. Wait until the temperature drops back down within the recommended range of 92°F to 98°F (indicated in green).

Step Four

After pouring the estimated amount of heat activator into the clean urine, replace and gently shake the contents to completely dissolve the Heat Activator, (usually takes 20 to 30 seconds).

After the Heat Activator granules have completely dissolved, read the temperature strip to ensure that the Solution is within the required temperature range of 92°F to 98°F (indicated in green).

Step Five

If necessary, carefully add a little more heat activator and repeat step 4.

Step Six

Once the clean urine solution is in the acceptable temperature range, remove the cap of the Mixing Container and pour the required amount of clean urine solution into the supplied specimen cup.